manualshive.com logo in svg

Bosch AMAX panel 2000 EN ICP-AMAX-P-EN, Installation Manual, Page: 59 / 92

Share
Download
Bosch AMAX panel 2000 EN ICP-AMAX-P-EN Installation Manual Download Page 59

AMAX panel 2000 / AMAX panel 2000 EN

 System Informations 2 | en

59

Bosch Sicherheitssysteme GmbH

Installation Manual

F.01U.241.127 | V4 | 2011.12

1.

Disarm: same as the Instant Zone disarm status

2.

AWAY Arm: same as the Delay Zone AWAY Arm status

3.

STAY Arm: 

This Zone will be Ignored and performed as disarm. 

Refer to Section Keypad Indicators, page 20 to see how the zone is displayed during exit 

time.

When System is disarmed and zone is not restored before, a Zone restore report is sent

5- Follower

The follower zone will perform as below:

1.

Disarm: 

same as the Instant Zone disarm status

2.

AWAY Arm:

Zone normal - no Alarm / no report

Zone triggered - Alarm / report

Zone triggered - during exit time - no Alarm / no report

Zone triggered - during entry time - no Alarm / no report

The remaining Delay Time is handed over from the Delay Zone to the Follower Zone.

The follower zone will performance as the same as a delay zone.

If there are two or more zones programmed as delay zones and both are triggered , 

thefollower zone will follow the first triggered delay zone

3.

STAY ARM: same as the delay zone.

When System is disarmed and zone is not restored before, a Zone restore report is sent.

6- Interior follower

The interior follower zone will perform as below:

1.

Disarm: same as the Instant Zone disarm status

2.

AWAY Arm: same as the Follower Zone AWAY Arm status

3.

STAY Arm: 

This zone will be ignored and performed as disarm. 

Refer to Section Keypad Indicators, page 20 to see how the zone is displayed during exit 

time.

When System is disarmed and zone is not restored before, a Zone restore report is sent.

7- 24 Hour Zone

The 24 Hour zone will perform as below:

1.

Disarm: 

Zone normal - no Alarm / no report

Zone triggered - Alarm / report

2.

AWAY Arm:

Zone normal - no Alarm / no report

Zone triggered - Alarm / report

Zone triggered - during exit time - Alarm / report

Zone triggered - during entry time - Alarm / report

3.

STAY Arm: Same as AWAY Arm performance.

A 24 Hour zone does not send a restore report until the zone is restored.

8- Tamper Zone

The Tamper zone will perform as below:

Summary of Contents for AMAX panel 2000 EN ICP-AMAX-P-EN





























































































Reviews:

No comments