manualshive.com logo in svg

Bosch AMAX panel 2000 EN ICP-AMAX-P-EN, Installation Manual, Page: 28 / 92

Share
Download
Bosch AMAX panel 2000 EN ICP-AMAX-P-EN Installation Manual Download Page 28

28

en | User Guide

AMAX panel 2000 / AMAX panel 2000 EN

F.01U.241.127 | V4 | 2011.12

Installation Manual

Bosch Sicherheitssysteme GmbH

4.10.4

Keypad medical alarm 

If you simultaneously press and hold [7] and [9], a silent keypad emergency medical alarm will 

be transmitted. Please contact your installer to enable/disable the emergency medical alarm 

functionality.

4.11

Domestic Dialing

4.11.1

Domestic Dialing Alarm

When the control panel is activated into zone tamper/zone alarm, it can dial the mobile phone 

or telephone number of a family member/friend. A maximum of one telephone number can be 

called through the control panel during an alarm.

Contact your installer to enable/disable the Domestic dialing functionality.

4.11.2

Confirming the Domestic call

All alarm events need acknowledgement.

The transmission sequence is repeated until the control panel recieves an acknowledgement 

tome.

The control panel automatically hangs up after 45 seconds if it cannot detect the 

acknowledgement tone and redial later.

The user presses [#] between two acknowledgement tones to confirm the alarm.

If the control panel got the [#] acknowledgement from the user, it will send 2 second long 

beep as acknowledge tone and hang up the line.

Summary of Contents for AMAX panel 2000 EN ICP-AMAX-P-EN





























































































Reviews:

No comments