manualshive.com logo in svg

Bosch AMAX panel 2000 EN ICP-AMAX-P-EN, Installation Manual, Page: 34 / 92

Share
Download
Bosch AMAX panel 2000 EN ICP-AMAX-P-EN Installation Manual Download Page 34

34

en | Fault and Tamper Description

AMAX panel 2000 / AMAX panel 2000 EN

F.01U.241.127 | V4 | 2011.12

Installation Manual

Bosch Sicherheitssysteme GmbH

4.

When the fault is reset, send the restored report to the configured destinations. The 

FAULT indicator is turned off when there is no other system fault.

5.3.2

Warning Device 1 Short

Condition:

Warning Device output is shorted.

Restore:

Warning Device output short is removed and fault is reset. 

Supervise:

1.

Monitor the voltage by MPU.

2.

Report the siren fault to the configured destination programmed on location 140.

3.

Slow flash FAULT indicator (refer to the detailed description in chapter keypad 

indicators)

4.

When the fault is reset, send the restored report to the configured destinations. The 

FAULT indicator is turned off when there is no other system fault.

5.3.3

Warning Device 2 Disconnected

Condition:

Warning Device is disconnected.

Restore:

Supervise:

1.

Monitor the voltage by MPU.

2.

Report the siren fault to the configured destination programmed on location 140.

3.

Slow flash FAULT indicator (refer to the detailed description in chapter keypad 

indicators)

4.

When the fault is reset, send the restored report to the configured destinations. The 

FAULT indicator is turned off when there is no other system fault

5.3.4

Warning Device 2 Short 

Condition:

Warning Device output is shorted.

Restore:

Warning Device output short is removed and fault is reset.

Supervise:

1.

Monitor the voltage by MPU.

2.

Report the siren fault to the configured destination programmed on location 140.

3.

Slow flash FAULT indicator (refer to the detailed description in chapter keypad 

indicators)

4.

When the fault is reset, send the restored report to the configured destinations. The 

FAULT indicator is turned off when there is no other system fault

5.4

Telephone Line Fault 

Condition:

Telephone line is broken or disconnected.

Restore:

Telephone line is restored or connected and fault is reset.

Supervise:

1.

Monitor the telephone line by MPU all the time when the telephone is idle.

2.

Report the telephone line fault to the configured destination programmed on location 

140.

Summary of Contents for AMAX panel 2000 EN ICP-AMAX-P-EN





























































































Reviews:

No comments