manualshive.com logo in svg

Bosch AMAX panel 2000 EN ICP-AMAX-P-EN, Installation Manual, Page: 74 / 92

Share
Download
Bosch AMAX panel 2000 EN ICP-AMAX-P-EN Installation Manual Download Page 74

74

en | System Informations 2

AMAX panel 2000 / AMAX panel 2000 EN

F.01U.241.127 | V4 | 2011.12

Installation Manual

Bosch Sicherheitssysteme GmbH

Figure 8.4

DX3010 Location Setting

8.6.6

B420/DX4020/ITS-DX4020G GSM GPRS Communication Module

The AMAX panel 2000 / AMAX panel 2000 EN Control Panel supports one B420 or one DX4020 

network communication module or ITS-DX4020G GSM/GPRS communication module. Only 

one can be selected to connect in one system to send reports thought the network.

Set in Location 134 to use B420/DX4020/ITS-DX4020G as below:

Figure 8.5

DX4020 Location Setting

ITS-DX4020G is configured by connecting with the PC. Refer to ITS-DX4020G manual for more 

information.

8.6.7

IUI-AMAX-LED8 8 Zone LED Keypad

This keypad operates with the AMAX panel 2000 / AMAX panel 2000 EN control panel. It 

provides indications for up to eight zones. The AMAX panel 2000 / AMAX panel 2000 EN 

support a maxmium of two keypad. To use the two keypads at the same time, jumper must be 

set to avoid address confliction.

–

Jumper off = address 1

–

Jumper short = address 2

8.6.8

IUI-AMAX-LCD8 8 Zone LCD Keypad

This keypad operates with the AMAX panel 2000 / AMAX panel 2000 EN control panel. This 

keypad has a fixed icon display and provides indications for up to eight zone. 

Summary of Contents for AMAX panel 2000 EN ICP-AMAX-P-EN





























































































Reviews:

No comments