Blohm + Voss Oil Tools FloorHand 9GF-1102 Technical Documentation Manual Download Page 22

Page: 22 / 105

INS
TA

ION

Rig-Up/ Rig-Down

•

Attach a two part lifting bridle to the lifting eyes on the uppermost portion of the frame
bracket using properly sized shackles. Attach one leg of the bridle to each bracket.

•

Take up the slack in the lifting bridle until the suspension assembly is just loose.

•

Remove the safety pin from the gimbal pin.

• Supporting the weight of the gimbal and suspension, remove the gimbal pin and lower

the gimbal and suspension to rest on the frame.

•

Replace the gimbal pin and safety pin.

•

Lift the unit with the bridle.

•

The installation of the unit is the reverse of the removal.

Summary of Contents for FloorHand 9GF-1102










































































































Search results

Summary of Contents for FloorHand 9GF-1102

Reviews:

Related manuals for FloorHand 9GF-1102

Brands by name

Popular brands

Blohm + Voss Oil Tools FloorHand 9GF-1102, Technical Documentation Manual

Search results

Summary of Contents for FloorHand 9GF-1102

Reviews:

Related manuals for FloorHand 9GF-1102

Brands by name

Popular brands