Blohm + Voss Oil Tools FloorHand 9GF-1102 Technical Documentation Manual Download Page 47

Page: 47 / 105

ION

Die Block Retaining Pin

Rod Head

Problem: Die block extends, but will not retract on its own.

Clamp the wrench in

question. It may be

necessary to clamp

the lower wrench

first.

Unclamp the same wrench.

Cylinder will retract. Observe

cylinder rod head using

flashlight through die block pin

installation hole.

Replace die block retaining pin.

See note!

Replace clamp cylinder.

Ensure pin hole in cylinder

rod is horizontal before

installation. See Note!

Has the die block

retaining pin been broken

or has the cylinder rod

head been broken?

NOTE: Replacement, remove

die block, ensure die block

cavity is free of all debris before

re-installation.

Yes

START

Summary of Contents for FloorHand 9GF-1102










































































































Search results

Summary of Contents for FloorHand 9GF-1102

Reviews:

Related manuals for FloorHand 9GF-1102

Brands by name

Popular brands

Blohm + Voss Oil Tools FloorHand 9GF-1102, Technical Documentation Manual

Search results

Summary of Contents for FloorHand 9GF-1102

Reviews:

Related manuals for FloorHand 9GF-1102

Brands by name

Popular brands