Bernina Artista 730 Instruction Manual Download Page 52

Page: 52 / 285

Practical Stitches – Applications

Zig-zag Stitch

TIP

Oversewing edges

If edges roll, use the Vari-overlock
stitch and foot No. 2A.

Zig-zag stitch No. 2
size and type suitable for the
fabric selected
cotton or polyester
up (sewing position)
Reverse pattern foot No. 1C

Zig-zag Stitch

•

suitable for all fabrics

•

overcasting

•

elastic seams

•

decorative sewing

Oversewing Edges

guide edge of fabric into the
center of the presser foot

do not select too wide a width or
too long a stitch – the edge should
lie flat and not roll

•

needle goes into fabric on one side
and over the edge into the air on
the other side

use a fine darning thread for
lightweight fabric

Satin Stitch

•

filled-in stitch used for appliqué,
embroidery, etc.

•

shorten stitch length, satin stitch
setting will be indicated by parallel
lines on stitch length bar

Stitch:

Needle:

Thread:

Feed dog:

Presser foot:

A
Zig-zag stitch with altered stitch length

B
Zig-zag stitch with altered stitch width

C
Finishing the edges with zig-zag stitch

Note:
The sewing computer has a programmed
satin stitch: No. 354 (see page 143).

TIP

Embroidery with satin stitch

Experiment with adjusting the stitch
width for new decorative effects.

032131.70.04_0509_a730_EN

Summary of Contents for Artista 730






























































































































































































































































































Search results

Summary of Contents for Artista 730

Reviews:

Related manuals for Artista 730

Brands by name

Popular brands

Bernina Artista 730, Instruction Manual

Search results

Summary of Contents for Artista 730

Reviews:

Related manuals for Artista 730

Brands by name

Popular brands