bergmann ALPHA-PACK-BIN Operating Instructions Manual Download Page 27

Page: 27 / 98

5. Operation

3) Once the locks are open, the PRESS BOX can

be tilted and emptied using the A receiving
vehicle.

4) After emptying, the lock, the container, the

door frame as well as the rubber seal (if any)
must be cleaned thoroughly.

For this purpose, use the pendulum
flap protection device (1).

Clean them with a water hose and a broom /

rubber broom from the side of the unloading
hatch / vehicle.

It is prohibited to stay behind or
underneath the unloading hatch.

5) Close the unloading hatch once the PRESS

BOX is horizontal again on the transport
vehicle.

Here, you first tighten the door using the

ratchet lever (1) and then close both of the
toggle closures (2).

Secure the crank arm (3) again through the

fastening bolt (4).

The following applies when
closing the pendulum-type
flap: first toggle, then ratchet.

4 3 1 2

Summary of Contents for ALPHA-PACK-BIN



































































































Search results

Summary of Contents for ALPHA-PACK-BIN

Reviews:

Related manuals for ALPHA-PACK-BIN

Brands by name

Popular brands

bergmann ALPHA-PACK-BIN, Operating Instructions Manual

Search results

Summary of Contents for ALPHA-PACK-BIN

Reviews:

Related manuals for ALPHA-PACK-BIN

Brands by name

Popular brands