bergmann ALPHA-PACK-BIN Operating Instructions Manual Download Page 44

Page: 44 / 98

7. The additional equipment

7.8

The electric lid opener

If required, the cover over the compaction
chamber can be hydraulically opened and
closed.

The operation is carried out via an addi-
tional keypad.

The lid opener is ready for us when both
EMERGENCY STOP buttons are
unlocked.

Press OPEN(1) in order to open the lid.
By activating the button CLOSE (2) the
compaction chamber is closed again.

electric
lid opener

7.9

Preliminary setup for a GSM unit

A preliminary setup for a GSM unit can be mounted on customer's request.

In that case, the control box is equipped with a power supply unit and an additional relay for a later
installation of the GSM signal device.

Summary of Contents for ALPHA-PACK-BIN



































































































Search results

Summary of Contents for ALPHA-PACK-BIN

Reviews:

Related manuals for ALPHA-PACK-BIN

Brands by name

Popular brands

bergmann ALPHA-PACK-BIN, Operating Instructions Manual

Search results

Summary of Contents for ALPHA-PACK-BIN

Reviews:

Related manuals for ALPHA-PACK-BIN

Brands by name

Popular brands