bergmann ALPHA-PACK-BIN Operating Instructions Manual Download Page 45

Page: 45 / 98

7. The additional equipment

7.10

The GSM complete package

The GSM unit with 900 to 1800 MHz can
send as a maximum three messages (e.g.
full signal or error message) to a maximum
of six addresses.

These messages are sent as SMS on a mo-
bile phone or as e-mail.
The customer has to provide a SIM card.

Programming of the call number and/or
text messages are carried out online via the
BERGMANN GSM module programming.

You will find more information on our
website:
www.bergmann-online.com (service).

Antenna

(the GSM unit is in the control box)

7.11

The ozone generator

With the help of the ozone generator
unpleasant odours are minimized by
chemical processes.

The generator is installed in the aggregate
room. Ozone is conducted via hoses into the
compaction chamber and, on request, also
into the container.

Ozone generator

Summary of Contents for ALPHA-PACK-BIN



































































































Search results

Summary of Contents for ALPHA-PACK-BIN

Reviews:

Related manuals for ALPHA-PACK-BIN

Brands by name

Popular brands

bergmann ALPHA-PACK-BIN, Operating Instructions Manual

Search results

Summary of Contents for ALPHA-PACK-BIN

Reviews:

Related manuals for ALPHA-PACK-BIN

Brands by name

Popular brands