bergmann ALPHA-PACK-BIN Operating Instructions Manual Download Page 63

Page: 63 / 98

12. Trouble - Shooting

12.

Problem

Source

Solution

Machine does not

4.1 Time relay for running

Replace time relay

switch off automa-

time defective

(see fig. 1, pt. 3)

tically

Compacting piston

5.1 The pressure at the

Please contact dealer

stops at top edge of

hydraulic valve is not

charging opening and

adjusted correctly

does not switch over
to front stroke

Oil is leaking out

6.1 Hydraulic hoses or screw

Tighten connections;

connections leaking

Replace hoses

Accessories

Container full signal

7.1 Time relay set wrong

Correct the time (see ch. 6.9.4)

reacts too late / too

or defective

or replace time relay

early

(see fig. 1, pt. 4)

Switching of container

8.1 Oil pressure switch

Please contact dealer

opening or closing

incorrectly set

does not work

8.2 Oil pressure switch

Please contact dealer

defective

Summary of Contents for ALPHA-PACK-BIN



































































































Search results

Summary of Contents for ALPHA-PACK-BIN

Reviews:

bergmann ALPHA-PACK-BIN, Operating Instructions Manual, Page: 63 / 98

Search results

Summary of Contents for ALPHA-PACK-BIN

Reviews: