background image

3.   Principle safety considerations

3.

 06

*

Maintenance work must be carried out on the stations intended for this purpose.

*

As far as necessary the repair area must be secured.

*

If  maintenance personnel have to access the machine through the unloading door, this door
must be secured by means of  an arresting cable. For this purpose, a snap hook is mounted on
the bottom of the container (see also chapter 5.3).

*

During maintenance work, the filling hole must be closed by the cover hood or scaffold boards.
If  necessary, use a certified ladder or work platform sufficient for the respective purpose. It is
the owner/user's responsibility to provide this equipment.

*

If required a certified ladder or platform appropriate for the respective purpose must be used.
These auxiliaries must be supplied by the operator.

*

Larger assemblies must be fixed and secured carefully with lifting devices when being replaced.

*

Hydraulic hoses must be replaced every 6 years as a minimum, even if  no safety relevant faults are
visible.

*

When handling oils, greases and other chemical substances, follow the safety instructions applicable
to the product.

*

Only use original spare parts in case of replacement.

*

After finishing service work check functioning of all safety devices (see chapter 3.2.3) and mount
again all lids, cleaning flaps, etc. and check them for tightness.

3.2.8 Instructions in case of emergency

*

Always press the 

EMERGENCY STOP

 button in emergency situations and pull the

mains plug. For the exact emergency procedure, refer to chapter 3.3.

*

Extinguish fire in the electric control with a CO2 extinguisher.

*

Burning oil must be extinguished using a Co2 extinguisher or dry powder extinguisher.

*

Location and operation of fire extinguishers must be made public. The possible measures of
fire detection and fire fighting must be observed.

Summary of Contents for ALPHA-PACK-BIN



































































































Reviews: