BendPak Autostacker PL-6SR Installation And Operation Manual Download

Page: 62 / 104

Autostacker™ Parking Lift

P/N 5900002 — Rev. D — August 2019

The following drawing shows the Control Stands at the

Rear

of the Lift.

To install the Control Stand at the

Rear

of the Lift

Find the 14-4 Cable and route it through the Bottom Connector Tube to the Conduit Fitting.

Use the 16-2 Cable to connect the Solenoids near the bottom of each Hydraulic Cylinder (two per
Lift).
Refer to

Wiring Diagrams

for wiring information.

Route the 16-6 Cable all the way through the Conduit Tube, then attach the wires to the wiring

coming out of the Bottom Connector Tube.
Refer to

Wiring Diagrams

for wiring information.

Remove the Cover of the Control Box to have access to the wiring inside.

Find the Control Stand, then route the other end of the 16-6 wire through the opening in the

Control Stand.

Connect the 16-6 wire to the Controls inside the Control Box.
Refer to

Wiring Diagrams

for wiring information.

⚠

DANGER

Do not connect the wires to the Power Unit at this point; that task is for an
Electrician. All wiring connections made to the Power Unit

must

be performed

by a licensed, certified Electrician.

Attach the Placard to the Control Stand, as described in the previous procedure.

Secure the Control Box to the Control Stand using a Screw, Washer, and Nut in each hole.

When you are ready to anchor the Control Stand, use the two holes on the Control Stand Base to

mark the locations on the ground.

Summary of Contents for Autostacker PL-6SR








































































































Search results

Summary of Contents for Autostacker PL-6SR

Reviews:

Related manuals for Autostacker PL-6SR

Brands by name

Popular brands

BendPak Autostacker PL-6SR, Installation And Operation Manual

Search results

Summary of Contents for Autostacker PL-6SR

Reviews:

Related manuals for Autostacker PL-6SR

Brands by name

Popular brands