BendPak Autostacker PL-6SR Installation And Operation Manual Download | Manualshive

Page: 35 / 104

background image

Autostacker™ Parking Lift

35

P/N 5900002 — Rev. D — August 2019

⚠

DANGER

Do not perform the following procedure until you are certain the Power Unit is
disconnected from power and cannot be re-energized. All electrical work must be

performed by a licensed, certified Electrician. If your organization has
Lockout/Tagout policies, make sure to implement them after connecting to a power

source.

To install the Power Disconnect Switch on an Autostacker

:

1.

Remove the two screws from the sides of the Electrical Box and remove the cover.

2.

Locate the three available wires: Black (Hot), White (Hot), and Green (Ground).

3.

Connect the three available wires to a User-supplied wiring.

4.

Connect the two Hot wires, Black and White, to the top of the Power Disconnect Switch.

5.

Route the Green (Ground) wire around the Power Disconnect Switch to the User-Supplied Power
Cord.

6.

Attach the Brown (Hot) and Blue (Hot) wires in the User-Supplied Power Cord to the bottom of the

Power Disconnect Switch.

7.

Replace the cover of the Electrical Box and screw it back on.

8.

Attach a Cable Clip to the inside of the Console, to hold the Power Cord securely; Cable Clips also

help support the weight of the Power Cord.
Cable Clips are

not

supplied with the Power Unit.

9.

Connect the User-Supplied Power Cord to an appropriate power source.

Install a Thermal Disconnect Switch

⚠

WARNING

The Autostacker comes with a

Power

Disconnect Switch, but the Autostacker

motor has no

thermal

overload protection.

Have an Electrician connect a Thermal Disconnect Switch or overload device that will make sure the

equipment shuts down in the event of an overload or an overheated motor.

⚠

DANGER

Installing a Thermal Disconnect Switch

must

be performed by a licensed, certified

Electrician. Do not perform

any

maintenance or installation on the lift without first

making sure that main electrical power has been disconnected from the lift and

cannot

be re-energized until all procedures are complete.

High running amps that exceed the motor’s full load amps (FLA) rating may result in permanent
damage to the motor.
Autostacker strongly recommends you

not

exceed the rated duty cycle of the Autostacker motor.

«
...
33
34
35
36
37
...
»

Summary of Contents for Autostacker PL-6SR









































































































Reviews:

No comments

Related manuals for Autostacker PL-6SR

Brand: Kargo Master Pages: 13

Brand: Kargo Master Pages: 21

Brand: Kargo Master Pages: 4

MOLLE PANELS RAM 2500

Brand: PUTCO Pages: 4

Brand: Westfalia Pages: 18

Brand: FormFit Pages: 4

Brand: IBASE Technology Pages: 100

S2000 Windscreen Camera Mount

Brand: Modifry Products Pages: 2

MagicComfort MSH200

Brand: Waeco Pages: 108

Brand: Tusk Pages: 2

Brand: Rola Pages: 3

Brand: NavLinkz Pages: 21

Brand: Kia Pages: 11

Brand: Saab Pages: 426

Brand: GMC Pages: 430

Brand: Westin Pages: 3

Brand: SNIPER Pages: 2

2010 Challenger SRT

Brand: Dodge Pages: 444

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands