BendPak Autostacker PL-6SR Installation And Operation Manual Download

Page: 56 / 104

Autostacker™ Parking Lift

P/N 5900002 — Rev. D — August 2019

Attach a Short Hydraulic Hose to each Hydraulic Line Assembly, then attach the other end of each

Hose to the Elbow Fitting on the Solenoid Valve Blocks.
The Solenoid Valve Blocks are

not

labeled S1 through S4; they are only labeled here to distinguish

between the various components.
The following drawing shows the hydraulic connections between two Autostackers.

Remove the Power Unit from its packaging, then place the Power Unit near the first Lift.

10.

Attach an Elbow Fitting (-04 JIC x -06 ORB) from the MPU Plumbing Kit to each Hydraulic Out Port
on the Power Unit.

11.

Connect the two Steel Hydraulic Lines from the MPU Plumbing Kit to the Hydraulic Elbow Fittings

you just connected to the Power Unit.

12.

Find the Medium and Extra-Long Hydraulic Hose from the MPU Plumbing Kit and connect them to

the Steel Hydraulic Lines using two Nipple Fittings.

13.

Connect the other end of the Medium Hydraulic Hose to the Tee Fitting attached to S1.

14.

Connect the other end of the Extra-Long Hydraulic Hose to the Tee Fitting attached to S2.

15.

Take a Long Hydraulic Hose from the Control Kit and connect it to the unattached end of the Tee

Fitting on S1.

16.

Using the components from the Control Kit for the next Lift, prepare the next set of Hydraulic

Cylinders.
Refer to steps 1-8 for additional instruction.

17.

Using the same Long Hose attached to S1 on the first Lift, connect the other end to the Tee Fitting

on S3 on the next Lift.

18.

Connect the second Long Hydraulic Hose to the Tee Fitting on S2 on the first Lift, then connect
the other end of the same Hose to the Tee Fitting connected to S4 on the next Lift.

19.

If there are no further Lifts to connect to, secure the unattached ends of the Tee Fittings with a Cap

Fitting, as shown in the following drawing.

Summary of Contents for Autostacker PL-6SR








































































































Search results

Summary of Contents for Autostacker PL-6SR

Reviews:

Related manuals for Autostacker PL-6SR

Brands by name

Popular brands

BendPak Autostacker PL-6SR, Installation And Operation Manual

Search results

Summary of Contents for Autostacker PL-6SR

Reviews:

Related manuals for Autostacker PL-6SR

Brands by name

Popular brands