BendPak Autostacker PL-6SR Installation And Operation Manual Download

Page: 13 / 104

Autostacker™ Parking Lift

P/N 5900002 — Rev. D — August 2019

Installation

This section describes how to install your Autostacker. Perform the steps in the order listed.

⚠

WARNING

Only use the factory-supplied parts that came with your Lift

. If you

use parts from a different source, you void your warranty and compromise the

safety of everyone who installs or uses the Lift. If you are missing parts, visit

autostacker.com/support

or call

(888) 977-8225

Safety Rules

When installing your Autostacker, your safety depends on proper training and thoughtful operation.

⚠

WARNING

Do not install this equipment unless you have automotive lift installation training.
Always use proper lifting tools, such as a Forklift or Shop Crane, to lift heavy

components. Do not install this equipment without reading and understanding
this manual and the safety labels on the unit.

Only fully trained personnel should be involved in installing this equipment.

Pay attention at all

times.

Use appropriate tools and lifting equipment, when needed. Stay clear of moving parts.

BendPak recommends referring to the current version of the ANSI/ALI ALIS Standard

Safety

Requirements for Installation and

Service for more information about safely installing, using, and

servicing your Lift.

⚠

WARNING

You must wear appropriate protective equipment

at all times

during

installation: gloves, steel-toed work boots, eye protection, back belts, and
hearing protection.

Tools

You may need some or all of the following tools:
•

Rotary hammer drill or similar

•

3/4", 3/8" masonry bits

•

Hammer and crow bar

•

Open-end wrench set

•

Socket and ratchet set

•

Medium crescent wrench

•

Chalk line and tape measure

•

Medium flat screwdriver

•

Fork lift or Shop Crane

Summary of Contents for Autostacker PL-6SR








































































































Search results

Summary of Contents for Autostacker PL-6SR

Reviews:

Related manuals for Autostacker PL-6SR

Brands by name

Popular brands

BendPak Autostacker PL-6SR, Installation And Operation Manual

Search results

Summary of Contents for Autostacker PL-6SR

Reviews:

Related manuals for Autostacker PL-6SR

Brands by name

Popular brands