BendPak Autostacker PL-6SR Installation And Operation Manual Download | Manualshive

Page: 5 / 104

background image

Autostacker™ Parking Lift

5

P/N 5900002 — Rev. D — August 2019

•

Keep loads centered and balanced on the Platform. Do not overload the rear side; Autostacker is

designed to support an equal load.

•

Use caution when driving onto the Platform with a Vehicle with wet tires.

•

When the product is in use, keep all body parts away from it.

•

Do not leave the area or the Autostacker without confirming that each Leg Base is secured on a

Safety Lock.

•

Make sure all operators read and understand the

Installation and Operation Manual

. Keep the

manual near the device at all times.

•

Make a visual inspection of the product before using it. Check for damaged or missing parts. Do

not use the product if you find any issues. Instead, take it out of service, then contact your

distributor, or Autostacker at

autostacker.com/support

or

[email protected]

•

Make a thorough inspection of the product at least once a year. Replace any damaged or severely
worn parts, decals, or warning labels.

Symbols

Following are the symbols used in this manual:

⚠

DANGER

Calls attention to an immediate hazard that

will

result in injury or death.

⚠

WARNING

Calls attention to a hazard or unsafe practice that

could

result in injury or death.

⚠

CAUTION

Calls attention to a hazard or unsafe practice that could result in minor personal
injury, product, or property damage.

NOTICE

Calls attention to a situation that, if not avoided, could result in product or property
damage.

Tip

Calls attention to information that can help you use your product better.

Liability Information

BendPak Inc. assumes

no

liability for damages resulting from:

•  Use of the product for purposes other than those described in this manual.
•  Modifications to the equipment without prior, written permission from BendPak Inc.
•  Damage to the equipment from external influences.
•  Incorrect operation of the equipment.

«
...
3
4
5
6
7
...
»

Summary of Contents for Autostacker PL-6SR









































































































Reviews:

No comments

Related manuals for Autostacker PL-6SR

Brand: Panasonic Pages: 2

CYRC50U - UNIVERSAL REAR-VIEW CAMERA

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 12

Brand: Jeep Pages: 6

Brand: GOgroove Pages: 9

Brand: Barker Pages: 2

Brand: Roav Pages: 10

Brand: Cadillac Pages: 368

Brand: Luverne Pages: 3

Brand: Navman Pages: 27

Brand: Toyota Pages: 636

Brand: Subaru Pages: 2

Brand: Subaru Pages: 328

Brand: Motoalliance Pages: 5

Brand: Thule Pages: 12

Brand: POOL-LINE Pages: 2

Brand: KLAUS Multiparking Pages: 72

Brand: Lock'er Down Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands