BendPak Autostacker PL-6SR Installation And Operation Manual Download

Page: 32 / 104

Autostacker™ Parking Lift

P/N 5900002 — Rev. D — August 2019

Depending on your Power Unit, the connector locations may be different. Use the drawing below to

identify your layout and then attach your Hydraulic Hoses and Return Line appropriately.

⚠

CAUTION

The Hydraulic Power Ports are almost always labeled

P1/P2

; the Hydraulic Return

Ports are commonly labeled

T1/T2

CV1/CV2

. Do not accidentally attach a

Hydraulic Hose to the Return Line Port. Your Autostacker will not work right unless

the Hydraulic Hoses and the Return Line are attached to the correct connector.

The following drawing shows the possible configurations for your Power Unit.

Not to scale. Not all components of the Power Unit shown

Summary of Contents for Autostacker PL-6SR








































































































Search results

Summary of Contents for Autostacker PL-6SR

Reviews:

Related manuals for Autostacker PL-6SR

Brands by name

Popular brands

BendPak Autostacker PL-6SR, Installation And Operation Manual

Search results

Summary of Contents for Autostacker PL-6SR

Reviews:

Related manuals for Autostacker PL-6SR

Brands by name

Popular brands