BendPak Autostacker PL-6SR Installation And Operation Manual Download Page 63

Page: 63 / 104

Autostacker™ Parking Lift

P/N 5900002 — Rev. D — August 2019

10.

Move the Control Stand out of the way, then drill two holes 3/8" wide by 4" (102 mm) deep in the

concrete floor at the locations you marked.
Go in straight; do not let the drill wobble. Use a carbide bit (conforming to the current ANSI
B212.15).

11.

Remove all dust from the holes.

12.

Use a wire brush, vacuum, hand pump, or compressed air. Do

not

ream the hole. Do

not

make

the hole any wider than the drill made it.

13.

Move the Control Stand in place over the two holes, then insert an Anchor Bolt with a Washer into

each hole, tapping it down into the hole.

14.

Wrench the Anchor Bolt clockwise to the recommended installation torque, 85-95 pound feet,

using a Torque Wrench.

Summary of Contents for Autostacker PL-6SR








































































































Search results

Summary of Contents for Autostacker PL-6SR

Reviews:

Related manuals for Autostacker PL-6SR

Brands by name

Popular brands

BendPak Autostacker PL-6SR, Installation And Operation Manual

Search results

Summary of Contents for Autostacker PL-6SR

Reviews:

Related manuals for Autostacker PL-6SR

Brands by name

Popular brands