BendPak Autostacker PL-6SR Installation And Operation Manual Download

Page: 27 / 104

Autostacker™ Parking Lift

P/N 5900002 — Rev. D — August 2019

Connect the Hydraulic Hoses

Hydraulic Hoses provide hydraulic power to the Hydraulic Cylinders, which is used to raise and lower

the lift.

If you have a Multi-Lift setup, this procedure will be different for you

; see

Multi-

Autostacker

towards the end of this manual for modified instructions.

The Autostacker comes with two Hydraulic Hoses, of different lengths:
•

Short Hydraulic Hose

. Goes from the Power Unit to the Hydraulic Cylinder

closest

the

Console.

•

Long Hydraulic Hose

. Goes from the Power Unit to the Hydraulic Cylinder

furthest

from

the

Console.
Both Hydraulic Hoses are routed through the Bottom Connector Tube, which is hollow.

The following drawing shows how the Hydraulic Hoses are routed to the Hydraulic Cylinders.

The following drawing is a close-up of the connections to make to the Hydraulic Cylinders.

Summary of Contents for Autostacker PL-6SR








































































































Search results

Summary of Contents for Autostacker PL-6SR

Reviews:

Related manuals for Autostacker PL-6SR

Brands by name

Popular brands

BendPak Autostacker PL-6SR, Installation And Operation Manual

Search results

Summary of Contents for Autostacker PL-6SR

Reviews:

Related manuals for Autostacker PL-6SR

Brands by name

Popular brands