BendPak Autostacker PL-6SR Installation And Operation Manual Download

Page: 16 / 104

Autostacker™ Parking Lift

P/N 5900002 — Rev. D — August 2019

•

Console

. The Console must be located near the Autostacker; the Hydraulic Hoses that come with

the Autostacker are optimized for up to 30 inches between the Autostacker and the Console.

Tip

If you want the Console further than 30 inches from the Autostacker, you can use
custom Hydraulic Hoses. Keep in mind that the Console

must

have a full,

unobstructed view of the Autostacker and be near the power source.

•

Operator

. The operator at the Console must have a full, unobstructed view of the Autostacker.

•

Power

. The Console must also be positioned near the power source.

Summary of Contents for Autostacker PL-6SR








































































































Search results

Summary of Contents for Autostacker PL-6SR

Reviews:

Related manuals for Autostacker PL-6SR

Brands by name

Popular brands

BendPak Autostacker PL-6SR, Installation And Operation Manual

Search results

Summary of Contents for Autostacker PL-6SR

Reviews:

Related manuals for Autostacker PL-6SR

Brands by name

Popular brands