BendPak Autostacker PL-6SR Installation And Operation Manual Download Page 28 | Manualshive

Page: 28 / 104

background image

Autostacker™ Parking Lift

28

P/N 5900002 — Rev. D — August 2019

To connect the Hydraulic Hoses

:

1.

Locate the two Hydraulic Hoses that come with your Lift.

2.

Starting near the Console, route the Long Hydraulic Hose through the Bottom Connector Tube

and pull it out at the Hydraulic Cylinder that is

furthest away

from the Console.

Leave enough Hose on the Console end to allow the Long Hydraulic Hose to be connected to the

Power Unit up through one of the openings at the bottom of the Console.
Pull out enough of the Hydraulic Hose to reach the Connector with Two Nuts when it is time to put

all of the components together.

3.

Starting near the Console, route the short Hydraulic Hose through the Bottom Connector Tube

and pull it out at the Hydraulic Cylinder nearest to the Console.
Leave enough of the Hydraulic Hose on the Console end to allow the Short Hydraulic Hose to be
connected to the Power Unit up through one of the openings at the bottom of the Console.
Pull out enough of the Hydraulic Hose to reach the Connector with Two Nuts when it is time to put

all of the components together.

4.

For both Hydraulic Cylinders, install Velocity Fuses in the connectors near the bottom of each
Hydraulic Cylinder. Finger tighten the connection.
Refer to

About Velocity Fuses

for more information.

5.

For both Hydraulic Cylinders, remove one Nut from the Connector with Two Nuts, put the

Connector with Two Nuts into the Connector Weldment, put the Nut you just removed back onto
the Connector with Two Nuts, and finger tighten both Nuts around the Connector Weldment.

6.

For both Hydraulic Cylinders, connect the Hydraulic Line Assembly to the top end of the Connector

with Two Nuts and the other end to the top end of the Velocity Fuse.
Finger tighten all connections.

7.

For both Hydraulic Cylinders, connect the Hydraulic Hose to the bottom end of the Connector with

Two Nuts.
Finger tighten the connections.

8.

Attach two 90° connectors (FTB ELB -04 JIC -06L ORB) to both Hydraulic Power connectors on

the Power Unit.
There are two Hydraulic Power connectors on a Power Unit, in varying locations (depending on the

Power Unit you have). Refer to

Connect the Power Unit

to identify your layout.

9.

Route the two Hydraulic Hoses, one at a time, through an opening along the bottom of the

Console and up to one of the 90° connectors, then connect them. It does not matter which

Hydraulic Line goes to which Hydraulic Power connector.

10.

Once all connections have been made, use the appropriate tools to fully tighten all of the finger-

tightened connections.

«
...
26
27
28
29
30
...
»

Summary of Contents for Autostacker PL-6SR









































































































Reviews:

No comments

Related manuals for Autostacker PL-6SR

Brand: Camcar Pages: 6

ESCALADE - BROCHURE 2009

Brand: Cadillac Pages: 24

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 20

Brand: GOgroove Pages: 9

Brand: Mazda Pages: 527

2008 Escalade EXT

Brand: Cadillac Pages: 496

Brand: Camcar Pages: 6

Brand: Metra Electronics Pages: 5

Brand: Renkforce Pages: 4

Brand: S3 Power Sports Pages: 2

2004 Impreza OUTBACK SPORT

Brand: Subaru Pages: 34

Brand: Mitsubishi MOTORS Pages: 416

Brand: rough country Pages: 4

Brand: iDataLink Pages: 6

PRIME DESIGN VCR-TC11B

Brand: Safe Fleet Pages: 12

Brand: RAM Pages: 148

Brand: Hamron Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands