BendPak Autostacker PL-6SR Installation And Operation Manual Download | Manualshive

Page: 37 / 104

background image

Autostacker™ Parking Lift

37

P/N 5900002 — Rev. D — August 2019

Add the Tire Trough and Tire Stops

The Tire Trough is a lowered section of the Platform that holds the tires of the Vehicle. The Tire Stops

attach to the top of the Tire Trough and add a bit of extra height for holding Vehicles with larger tires.

Important

: The Tire Trough functions as a tire chock; the forward wheels of the Vehicle on the

Platform should

always

be sitting fully in the Tire Trough.

The Tire Trough is installed at the front of the Autostacker; it attaches to the Top Connector Tube.
The Tire Stops are optional but recommended. They attach to the Top Connector Tube using the

same Nuts, Bolts, and Washers as the Tire Trough.

⚠

WARNING

The Tire Trough is heavy. Move it into position using a lifting device such as a
Forklift or Shop Crane. If this is not an option, have at least two people to move it.

Do not allow just one person to move the Tire Trough

; they could be

injured.

To install the Tire Trough and Tire Stops

:

1.

Move the Tire Trough into position next to the Top Connector Tube.
A section of the Tire Trough rests on the Top Connector Tube. This is where the Tire Stops go and

where you attach the Tire Trough to the Top Connector Tube.

2.

Get the necessary Bolts (4), Nuts (4), and Washers (8) from the Parts Bag.

3.

Put the Tire Stops on top of the Tire Trough; align the holes in the bottom of the Tire Stops with
the holes in the Tire Trough and the Top Connector Tube.
Orient the Tire Stops so that the vertical portion is on the Tire Trough side.

4.

Push a Washer into place on the Bolt, then slide the Bolt through the Tire Stop, the Tire Trough,
and the Top Connector Tube.

5.

Put the second Washer on the Bolt, at the bottom, then add and tighten the Nut.
The following drawing is a side view of how these components go together.

6.

Repeat steps 4 and 5 for each of the other holes.

«
...
35
36
37
38
39
...
»

Summary of Contents for Autostacker PL-6SR









































































































Reviews:

No comments

Related manuals for Autostacker PL-6SR

Brand: AA Products Pages: 6

Brand: iDataLink Pages: 106

Brand: Toyota Pages: 56

Gasoline/Electric DS Golf Car 1996

Brand: Club Car Pages: 48

adaptiv mini ADVM-BM1

Brand: Connects2 Pages: 4

Brand: Jeep Pages: 136

Brand: Thule Pages: 12

Brand: Billien Pages: 2

Brand: Lexus Pages: 28

Brand: Vauxhall Pages: 95

Brand: ORA Pages: 7

Brand: Jaeger Pages: 14

Brand: Edelbrock Pages: 1

Brand: Westin Pages: 3

Brand: Whelen Engineering Company Pages: 4

Brand: Hama Pages: 39

Brand: Whispbar Pages: 34

Brand: Federal Signal Corporation Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands