BendPak Autostacker PL-6SR Installation And Operation Manual Download | Manualshive

Page: 66 / 104

background image

Autostacker™ Parking Lift

66

P/N 5900002 — Rev. D — August 2019

⚠

DANGER

All wiring

must

be performed only by a licensed, certified Electrician. Do not

perform any maintenance or installation on the Lift without first making sure that

main electrical power has been disconnected from the Lift and cannot be re-
energized until all procedures are complete. If your organization has

Lockout/Tagout policies, implement them after connecting to a power source.

To connect to a power source

:

1.

Have a certified, licensed Electrician connect an appropriate plug to the wiring, coming out of the

Power Unit.
The plug is

not

supplied with the Power Unit.

2.

Connect the power source cable to the plug you just connected.
The power source cable is

not

supplied with the Power Unit.

Refer to

Wiring Diagrams

for wiring information.

3.

Connect the Control Stands to the Power Unit.
Refer to

Wiring Diagrams

for wiring information.

4.

Connect the Power Disconnect Switch.
Refer to

Wiring Diagrams

for wiring information.

5.

Have a certified, licensed Electrician check for any loose connections.

6.

Fill the Hydraulic Fluid Reservoir.
The Power Unit’s Hydraulic Fluid reservoir must be filled with Hydraulic Fluid or Automatic

Transmission Fluid before you begin operation. When you receive it, the reservoir is empty; the

Power Unit will not work correctly until there is an adequate supply of the approved fluids.
Approved fluids are any general purpose ISO-32, ISO-46, or ISO-68 hydraulic oil or approved

automatic transmission fluids such as Dexron III, Dexron VI, Mercon V, Mercon LV, or any synthetic

multi-vehicle automatic transmission fluid.

⚠

WARNING

Do not run the Power Unit without Hydraulic Fluid; you will damage it. Keep the
Power Unit dry; damage the Power Unit caused by water, detergents, acids, and

other liquids is not covered by the warranty.

«
...
64
65
66
67
68
...
»

Summary of Contents for Autostacker PL-6SR









































































































Reviews:

No comments

Related manuals for Autostacker PL-6SR

Keystation Mini 32

Brand: M-Audio Pages: 45

Brand: M-Audio Pages: 27

PROKEYS SONO 61

Brand: M-Audio Pages: 49

Brand: M-Audio Pages: 38

Brand: Pacbrake Pages: 14

Brand: Phonocar Pages: 6

Brand: Yakima Pages: 13

Brand: Menabo Pages: 11

Automotive 31006

Brand: KRAFTWERK Pages: 2

v.LOGiC Intelligent Solution V5-NTG46

Brand: Caraudio-Systems Pages: 18

Brand: tams elektronik Pages: 44

Evo All THAR-FOR3

Brand: Fortin Pages: 7

Brand: RAM Pages: 496

Brand: Cadillac Pages: 352

Brand: Scosche Pages: 12

HOLLANDIA 700 - 20 Series

Brand: Webasto Pages: 30

Brand: PEUGEOT Pages: 404

Brand: KAP Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands