Belanger Chameleon Arch Series Owner'S Manual Download Page 66

Page: 66 / 90

CHAMELEON® ARCH SERIES

Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

1MANUL526

Installation

Leak Test / Nozzle Kit Installation (Applies only to the Spray Arch Option)

1) Electrically connect water solenoid valve or other optional equipment to the car wash

controller unit (if applicable).

2) Flush the system lines and manifolds.

3) Locate the selected nozzle kit and install the nozzles according to the nozzle

configuration guide beginning on the next page.

Note:

Lubricate nozzles with liquid Teflon (NO TAPE) for easier installation and

maintenance.

4) Run water through the Arch and verify that there are no leaks at any of the fitting or

nozzle locations.

Note:

Nozzle selection is dependant on application, Nozzles vary for High-Pressure,

Reclaim, Pre-Soak, Waxes and R.O.

Summary of Contents for Chameleon Arch Series



























































































Search results

Summary of Contents for Chameleon Arch Series

Reviews:

Related manuals for Chameleon Arch Series

Brands by name

Popular brands

Belanger Chameleon Arch Series, Owner'S Manual

Search results

Summary of Contents for Chameleon Arch Series

Reviews:

Related manuals for Chameleon Arch Series

Brands by name

Popular brands