Belanger Chameleon Arch Series Owner'S Manual Download Page 39

Page: 39 / 90

CHAMELEON® ARCH SERIES

1MANUL526

Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

Installation

Additional Options: Foam Pods

Note:

Foam Pods can be mounted to either the Spray Arch or the Utility Arch.

Things You Should Know About the Foam Pod Option

The Foam Pods can be mounted in two ways. See the images below for details.

Standard Mounting

The image above shows the Triple Foaming Foaming Pods. The Single Foaming Pods mount the same way.

Reverse Mounting

The image above shows the Triple Foaming Foaming Pods. The Single Foaming Pods mount the same way.

Note:

Above images show Sunburst Pendant.

Triple Faom

Pod

Single

Foam Pod

Triple Faom Pod

Mounted Up

Single Foam Pod

Mounted Up

Summary of Contents for Chameleon Arch Series



























































































Search results

Summary of Contents for Chameleon Arch Series

Reviews:

Related manuals for Chameleon Arch Series

Brands by name

Popular brands

Belanger Chameleon Arch Series, Owner'S Manual

Search results

Summary of Contents for Chameleon Arch Series

Reviews:

Related manuals for Chameleon Arch Series

Brands by name

Popular brands