Belanger Chameleon Arch Series Owner'S Manual Download Page 26

Page: 26 / 90

CHAMELEON® ARCH SERIES

Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

1MANUL526

Installation

Arch Assembly

11)

Spray Arch Only:

Place the spacer over the nipple on the top of the spray manifold

assembly and secure it with the 1/4-20 set screw as shown in the image.

The height of the horizontal manifold may need to be adjusted later in the installation to
accommodate the holes and the vertical filler strips.

Note:

Be sure the setscrew faces the exit of the tunnel.

12)

Spray Arch Only:

Apply Teflon tape and liquid Teflon to the threads of the nipple and

tighten

the supplied 1/2” (12.7 mm) coupling to the top spray manifold.

Before

After

Before

After

Summary of Contents for Chameleon Arch Series



























































































Search results

Summary of Contents for Chameleon Arch Series

Reviews:

Related manuals for Chameleon Arch Series

Brands by name

Popular brands

Belanger Chameleon Arch Series, Owner'S Manual

Search results

Summary of Contents for Chameleon Arch Series

Reviews:

Related manuals for Chameleon Arch Series

Brands by name

Popular brands