Belanger Chameleon Arch Series Owner'S Manual Download Page 52

Page: 52 / 90

CHAMELEON® ARCH SERIES

Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

1MANUL526

Installation

Additional Options: Single K-Nozzle Manifolds

Single K-Nozzle Manifold Installation

1) Locate the box that the K-Nozzle components shipped in and confirm that all of the

pieces are there and also that there is no damage to any of the components.

2) Remove the two foam tube assemblies, the driver side spray manifold assembly and the

passenger side spray manifold assembly. The side spray manifolds are labeled with a
tag.

3) Apply Teflon

™ tape and liquid Teflon™ to the threads on the ends of both side spray

manifolds.

4) Mount a foam tube assembly to the end of each manifold. When you tighten the foam

tube assemblies to the manifolds, make sure that the elbow fittings (shown in dotted
ovals below) face away from the center of the bay.

After

Before

Apply Teflon™ tape and
liquid Teflon™ here

Apply Teflon™ tape and
liquid Tef

lon™ here

Summary of Contents for Chameleon Arch Series



























































































Search results

Summary of Contents for Chameleon Arch Series

Reviews:

Related manuals for Chameleon Arch Series

Brands by name

Popular brands

Belanger Chameleon Arch Series, Owner'S Manual

Search results

Summary of Contents for Chameleon Arch Series

Reviews:

Related manuals for Chameleon Arch Series

Brands by name

Popular brands