Belanger Chameleon Arch Series Owner'S Manual Download Page 24

Page: 24 / 90

CHAMELEON® ARCH SERIES

Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

1MANUL526

Installation

Arch Assembly

Using the third joint block weldment, connect and secure the two head beams together

as shown in the image

Note:

If you have a Utility Arch, proceed to the “Tunnel Placement” section. If you have Spray

Arch, continue to step #6.

Lay the partially completed Arch on the ground. Place protective material between the
ground and the Arch to keep it from getting scratched while you work on it.

Spray Arch Only:

Remove the top spray manifold assembly from the skid. It should

have the nozzle extensions and the barbed hose fittings already in place.

Nozzle Extension (4)

Barbed Hose Fitting (2)

Summary of Contents for Chameleon Arch Series



























































































Search results

Summary of Contents for Chameleon Arch Series

Reviews:

Related manuals for Chameleon Arch Series

Brands by name

Popular brands

Belanger Chameleon Arch Series, Owner'S Manual

Search results

Summary of Contents for Chameleon Arch Series

Reviews:

Related manuals for Chameleon Arch Series

Brands by name

Popular brands