Belanger Chameleon Arch Series Owner'S Manual Download Page 63

Page: 63 / 90

CHAMELEON® ARCH SERIES

1MANUL526

Belanger, Inc. * PO BOX 5470 * Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

Installation

Additional Options: Dual K-Nozzle Manifolds

Dual K-Nozzle Manifold Installation

16) From the corner of the head beam, you will proceed to run the airlines through the

extruded side of the legs.

17) Locate the Filler Strip Kit and the remove the two sections that are for the head beam

and the section that is for the upper half of the Arch leg weldments. Snap all four filler
strips in, making sure t

hat you are not pinching any of the 3/8” (9.52 mm) airlines. Refer

to the images below for more detail.

18) Remove the four sections that are for the lower half of each Arch leg weldment. Snap

the upper section into each leg first.

19) On each of the lower sections, there is a slotted area.

They will be used to run the airlines through. Run the lines through the slotted area and
then snap the filler strip into place. Refer to the images below for more detail.

Nylon sleeves

go in here

Summary of Contents for Chameleon Arch Series



























































































Search results

Summary of Contents for Chameleon Arch Series

Reviews:

Related manuals for Chameleon Arch Series

Brands by name

Popular brands

Belanger Chameleon Arch Series, Owner'S Manual

Search results

Summary of Contents for Chameleon Arch Series

Reviews:

Related manuals for Chameleon Arch Series

Brands by name

Popular brands