Baroness LM315GG Owner'S Operating Manual Download Page 24

Caution

The radiator cap is pressurized.
If you remove the radiator cap while the
engine is overheated, hot steam will burst
out, possibly resulting in burns.
Make sure that the water temperature and
pressure are reduced, and then grab the cap
with a thick cloth and gradually open the cap.

Important

When you supply coolant, be sure to use
clean water, such as tap water.
During winter, remove coolant. Alternatively,
mix long-life coolant and clean water, and
then pour it into the radiator and reserve tank.

Relationship between concentration of long-life
coolant (LLC) and freezing temperature

Freezing temperature

LLC concentration

(volume %)

Down to -10 °C (14 °F)

20 %

Down to -15 °C (5 °F)

30 %

Down to -20 °C (-4 °F)

35 %

Down to -25 °C (-13 °F) 40 %

If the coolant level in the reserve tank is
lower than the "LOW" mark, open the
reserve tank cap and fill the tank with clean
water up to the "FULL" mark.

1

ouuoov-009

Coolant Supply_001

1

Reserve tank

If no coolant is in the reserve tank, follow
the steps below to fill the tank with clean
water.

Open the radiator cap, and then supply
clean water up to the opening.

1.

2.

[1]

Open the reserve tank cap, and then
supply clean water up to the "FULL"
mark.

1

2

ouuoov-010

Coolant Supply_002

1

Radiator cap

2

Radiator

Change of Coolant

For details on handling the engine, please refer
to the separate Engine Handling Manual.

Warning

When you replace the coolant, be sure to
drain it into a bowl and discard it in
accordance with local laws and regulations.

Warning

Do not touch the radiator or coolant during
engine operation or right after the engine has
been turned off.
Otherwise, you may get burned due to high
temperatures.
After the radiator has well cooled down, open
the radiator cap.

Caution

Change coolant after the engine has well
cooled down.

Important

When you change coolant, be sure to use
clean water, such as tap water.
During winter, remove coolant. Alternatively,
mix long-life coolant and clean water, and
then pour it into the radiator and reserve tank.

[2]

LM315GC

Handling Instructions

Page 4-4

Inspection Before Use

Summary of Contents for LM315GG












































































Reviews: