Bandai Namco MAXIMUM TUNE 5DX PLUS Operation Manual Download

Page: 98 / 186

8b-2-2 Underbox assembly

Symptom

Cause

Action

reference

page

• Sound is not output

from the woofer
speaker.

• The volume setting is low.

• Set the appropriate volume.

page 51

• The connector or Faston

terminal is disconnected.

• Insert the connector and Faston terminals securely. page 113

• A D2 Amp pC board

malfunction.

• replace the D2 Amp pC board.

page 113

• A DOT ONE pC board

malfunction.

• replace the DOT ONE pC board.

page 115

• IC cards are not

dispensed.

• There are no

BANApASSpOrT cards in
the IC card vendor.

• Add BANApASSpOrT cards.

page 69

• A BANApASSpOrT card is

jammed.

• remove the jammed BANApASSpOrT card.

page 71

• A connector is

disconnected.

• Insert the connector securely.

page 105

8b-2-3 Monitor assembly

Symptom

Cause

Action

reference

page

• Images are not

displayed.

• The monitor power is off.

• Turn on the monitor power.

page 127

• A connector is

disconnected.

• Insert the connector securely.

page 124

• A monitor malfunction.

• replace the monitor.

page 124

• Sound is not output

from the monitor
bottom speaker.

• The volume setting is low.

• Set the appropriate volume.

page 51

• The connector or Faston

terminal is disconnected.

• Insert the connector and Faston terminals securely. page 113

• A D2 Amp pC board

malfunction.

• replace the D2 Amp pC board.

page 113

• The View Change

button or Challenge
ON/OFF button does
not function.

• A connector is

disconnected.

• Insert the connector securely.

page 118

• A button malfunction.

• replace the button.

page 118

• The View Change

button or Challenge
ON/OFF button does
not light up.

• A connector is

disconnected.

• Insert the connector securely.

page 118

• A button light malfunction.

• replace the illuminated button light.

page 118

• IC cards are not

recognized.

• The BANApASSpOrT

card reader/writer lED
does not light up.

• The card reader/writer

connector is disconnected.

• Insert the connector securely.

page 119

• A card reader/writer

malfunction.

• Contact your distributor.

• The monitor side lEDs

do not light up.

• A connector is

disconnected.

• Insert the connector securely.

page 123

• A Squid ring pC board

malfunction.

• replace the Squid ring pC board.

page 123

8b. Service

- Must be performed by a technician -

WMT5DX取扱説明書_EN.indb 96

16/03/22 19:54

Summary of Contents for MAXIMUM TUNE 5DX PLUS



























































































































































































Search results

Summary of Contents for MAXIMUM TUNE 5DX PLUS

Reviews:

Related manuals for MAXIMUM TUNE 5DX PLUS

Brands by name

Popular brands

Bandai Namco MAXIMUM TUNE 5DX PLUS, Operation Manual

Search results

Summary of Contents for MAXIMUM TUNE 5DX PLUS

Reviews:

Related manuals for MAXIMUM TUNE 5DX PLUS

Brands by name

Popular brands