background image

Time Attack Mode

• In this game mode, the player races on a course alone, without any rival cars or other cars, to compete

 

against time.

• When the player crosses the finish line within the specified time, the lap time is displayed on the result screen.
• When a player using a BANApASSpOrT card beats their best time for that course, the new record is

 

registered to the server.

• When the player has raced on the course before, the split time difference from the player’s best time is

 

displayed at various locations along the course.

• If the player does not cross the finish line within the specified time, the game ends (Time Up).

vS player Mode

• When “Accept VS Challengers” is selected at the start of game play, players at other communication-linked 

cabinets can intrude into the game.

• In a VS player game, players race against each other.
• To win the race, a player must cross the finish line before the other players.
• When the remaining time reaches “0”, the game ends (Time Up) and the player in the leading position at

 

that point becomes the winner.

• The winning player receives VS player stars according to the race results, and can play another game.

(The display returns to the game mode selection screen.)
* Whether or not the winner remains and plays another game can be set in the Test mode.

• The players in second or following places can also receive VS player stars according to the race results.
• players can receive VS player awards according to the number of opponents they beat. By collecting VS

 

player awards, players can raise their VS player rank and at the same time receive an aura motif.

• Direction selection panels appear before branch points on the course. The player in the leading position

 

can determine the direction of the race by passing either the left or right panel.

About Discarded vehicle Cards

• Discarded Vehicle Cards can be given as presents to other BANApASSpOrT cards at the Wangan

 

Terminal. They cannot be used with the player’s own BANApASSpOrT card. (Cards are given using the

 

Wangan Terminal.)

• The player gains a single Discarded Vehicle Card after every 60 game plays.
• A single BANAPASSPORT card can stock up to five Discarded Vehicle Cards.

*  Discarded Vehicle Cards created up to Maximum Tune 3DX plUS cannot be used.

• When a Discarded Vehicle Card is used, the game starts from the following status when registering a new

 

vehicle.

Story Mode ………………………… 20th episode cleared
Tuning ……………………………… 600 Hp/B (Step 20)

Obtaining and changing body colors * Except some models

• The player gains a custom body color after every 60 game plays. This allows the player to paint their vehicle 

body any color from among those they have gained.

7. Operation

28

WMT5DX取扱説明書_EN.indb   28

16/03/22   19:53

Summary of Contents for MAXIMUM TUNE 5DX PLUS



























































































































































































Reviews: