Bandai Namco MAXIMUM TUNE 5DX PLUS Operation Manual Download | Manualshive

Page: 2 / 186

background image

Introduction

Thank you very much for purchasing MAXIMUM TUNE 5DX

PLUS

(referred to as “this product” in this manual). This product

consists of the Driver Cabinet (referred to as the “machine” in this manual) and the Wangan Terminal.

This Operation Manual describes:
• Information needed to correctly understand the machine.
• How to safely install, move, transport, operate, service and dispose of the machine.
• How to make full use of the machine’s functions and operate it correctly.
• How to ensure the safety of players and bystanders.

In addition to this Operation Manual, the following manual is also supplied separately.

MANUAl (supplied with

• MAXIMUM TUNE 5DX

PLUS

- WANGAN TErMINAl OpErATION

the Wangan

Terminal)

• MAXIMUM TUNE 5DX

PLUS

- EVENT MODE SETTING MANUAl

Contact for this machine and machine repair inquiries
• For inquiries regarding the machine or machine repairs, contact your distributor.

The copyrights, trademarks and other rights used by the machine are noted at the end of this Operation
Manual.

WMT5DX取扱説明書_EN.indb 2

16/03/22 19:53

«
1
2
3
4
...
»

Summary of Contents for MAXIMUM TUNE 5DX PLUS



























































































































































































Reviews:

No comments

Related manuals for MAXIMUM TUNE 5DX PLUS

Brand: AMS Pages: 50

Brand: Atari Pages: 90

Brand: jakar Pages: 3

Brand: Icegame Pages: 87

JETBALL ALLEY G4K

Brand: UNIS Pages: 63

Brand: Unitec Pages: 22

Brand: Merit Pages: 33

Brand: Williams Pages: 79

Brand: Triumph Sports USA Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands