Home
/
Bandai Namco
/
MAXIMUM TUNE 5DX PLUS
/
Operation Manual

Bandai Namco MAXIMUM TUNE 5DX PLUS, Operation Manual

Share

Page: 15 / 186

background image

5. Installation

5-1 Installation Conditions

z

z

Do not block the ventilation holes on the back side of the machine with any objects or a wall, etc.
If the ventilation holes are blocked, the inside of the machine may become hot and result in fire or
malfunction.

5-1-1 Installation locations to Avoid

z

z

The machine is designed for indoor use. Never install the machine outdoors or in the following loca-
tions.
•  A location exposed to direct sunlight
•  A location exposed to rain or water leaks
•  A damp location
•  A dusty location
•  A location close to heaters
•  A hot location
•  An extremely cold location
•  A location exposed to condensation caused by temperature differences
•  A location that obstructs an emergency exit or fire extinguishing equipment
•  An unstable location or a location exposed to vibration

13

1

2

3

4

5

6

7

8A

8B

9

10

11

12

Installation

Test Mode

Troubleshooting

WMT5DX取扱説明書_EN.indb 13

16/03/22 19:53

«
...
13
14
15
16
17
...
»

Summary of Contents for MAXIMUM TUNE 5DX PLUS



























































































































































































Reviews:

No comments

Related manuals for MAXIMUM TUNE 5DX PLUS

Brand: WAHLAP TECH Pages: 121

Brand: UNIS Pages: 27

SHOOTING CHANCE

Brand: Andamiro Pages: 18

Brand: Panda Vending Pages: 4

Brand: UNIS Pages: 28

Brand: Kamasa-TOOLS Pages: 8

Injustice Arcade

Brand: Raw Thrills Pages: 56

Brand: Formax Pages: 16

Brand: Formax Pages: 29

Brand: Formax Pages: 113

Brand: Vendors Exchange Pages: 28

Brand: LG Pages: 72

Brand: LG Pages: 48

Brand: UNIS Pages: 99

Street Basketball with LED

Brand: SAINT-FUN Pages: 12

Brand: MecPower Tecway Pages: 17

Brand: Westomatic Pages: 150

Brand: Stern Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands