Bandai Namco MAXIMUM TUNE 5DX PLUS Page 140 Operation Manual Download

Page: 140 / 186

remove the stopper arm B from the steering motor shaft, and remove the key and spacer.

Remove the four flanged bolts (M8 x 20), and remove the sub frame.

replace the steering motor with a new one.

Sub frame

Spacer

Stopper arm B

Key

Label
* Install with the label
facing upward

Steering motor

Flanged bolt (M8 x 20)

To install, perform the procedure in reverse.
Install the steering motor with the label facing upward.

After replacement, be sure to check the steering operation.

(See “7-9 Adjustments after parts replacement (GO TO I/F INITIAlIZE)” on page 68.)

8b. Service

138

- Must be performed by a technician -

WMT5DX取扱説明書_EN.indb 138

16/03/22 19:54

Summary of Contents for MAXIMUM TUNE 5DX PLUS



























































































































































































Search results

Summary of Contents for MAXIMUM TUNE 5DX PLUS

Reviews:

Related manuals for MAXIMUM TUNE 5DX PLUS

Brands by name

Popular brands

Bandai Namco MAXIMUM TUNE 5DX PLUS, Operation Manual

Search results

Summary of Contents for MAXIMUM TUNE 5DX PLUS

Reviews:

Related manuals for MAXIMUM TUNE 5DX PLUS

Brands by name

Popular brands