iv
I-E96-607A
Table of Contents
(continued)
Page
®
SECTION 3 - INSTALLATION
(continued)
UNPACKING AND INSPECTION.................................................................................... 3-2
INIIR01 INFI-NET TO INFI-NET REMOTE INTERFACE INSTALLATION ......................... 3-2
Termination Unit/Module Configuration and Installation ....................................... 3-3
NTCL01 or NICL01 Installation ........................................................................ 3-3
NTMP01 or NIMP01 Installation ...................................................................... 3-3
INNIS01 Module Dipswitches ................................................................................. 3-4
INNIS01 Dipswitch SW1, Node Address ........................................................... 3-4
INNIS01 Dipswitch SW2, Loop Address ........................................................... 3-4
INNIS01 Dipswitch SW3, Loop Mode................................................................ 3-5
INNIS01 Dipswitch SW4, Event and Error Counters ........................................ 3-6
User-Configured Jumpers ............................................................................... 3-8
Power System Status....................................................................................... 3-8
INIIT02 Module Dipswitches .................................................................................. 3-9
INIIT02 Module Jumpers ................................................................................. 3-9
INIIT02 Test/Module Address Dipswitches SW3 .............................................. 3-9
INIIT02 Dipswitch SW4, Options ..................................................................... 3-9
INIIR01 Interface Mounting Unit Preparation ....................................................... 3-11
Checking the Module Mounting Unit for -30 VDC .......................................... 3-12
INIIT02 Installation Options .......................................................................... 3-12
Isolating Controlway and I/O Expander Bus .................................................. 3-12
Installing the INIIR01 Interface Modules .............................................................. 3-13
INIIT02 Executive Block Initialization .................................................................. 3-16
Installing the Optional Digital I/O Module ........................................................... 3-16
INIIL02 INFI-NET TO INFI-NET LOCAL INTERFACE INSTALLATION ........................... 3-17
NTCL01 or NICL01 Installation ............................................................................ 3-18
INNIS01 Dipswitches and Jumpers ...................................................................... 3-18
INIIT03 Dipswitches and Jumpers ....................................................................... 3-18
INIIT03 Dipswitch UUB0, Module Address ..................................................... 3-18
INIIT03 Dipswitch UMB1, Module Options and Diagnostics ........................... 3-19
INIIT03 Dipswitch LMB2, Module Options ..................................................... 3-19
INIIT03 Dipswitch LLB3, Diagnostics ............................................................. 3-20
Jumpers J1, J2, J4, J5 ................................................................................. 3-21
HW Setup Dipshunt ...................................................................................... 3-22
INIIL02 Interface Module Mounting Unit Preparation ........................................... 3-22
Checking the Module Mounting Unit for -30 VDC .......................................... 3-23
INIIT03 Installation Options .......................................................................... 3-23
Isolating Controlway and I/O Expander Bus .................................................. 3-23
INSTALLING THE INTERFACE MODULES .................................................................. 3-24
SECTION 4 - OPERATING PROCEDURES................................................................................4-1
INTRODUCTION .......................................................................................................... 4-1
INNIS01 MODULE START-UP PROCEDURES ............................................................... 4-1
Event Counters ..................................................................................................... 4-1
Error Counters ...................................................................................................... 4-1
INIIT02 MODULE LEDs AND CONTROLS ..................................................................... 4-2
Red/Green Status LED.......................................................................................... 4-2
CPU LEDs ............................................................................................................. 4-2
Stop/Reset Switch ................................................................................................. 4-4
INIIR01 MODES OF OPERATION ................................................................................. 4-4
Execute Mode ........................................................................................................ 4-4
Configure Mode ..................................................................................................... 4-4
INIIT02 EXECUTIVE BLOCK CONFIGURATION ............................................................ 4-4
DETERMINING INIIT02 MODULE POINT COUNT ......................................................... 4-5
