vi
I-E96-607A
Table of Contents
(continued)
Page
®
APPENDIX E - INIIR01 REDUNDANT CONFIGURATIONS...................................................... E-1
INTRODUCTION ..........................................................................................................E-1
REDUNDANT CONFIGURATIONS ................................................................................E-1
Switch Settings for Redundancy ............................................................................E-1
Redundant Hardware Configuration Example ........................................................E-1
Redundant Termination Units/Modules.................................................................E-2
List of Figures
No.
Title
Page
1-1.
INFI-NET to INFI-NET Remote Interface ................................................................. 1-2
1-2.
INFI-NET to INFI-NET Local Interface..................................................................... 1-3
3-1.
INNIS01 Module Circuit Board Layout ................................................................... 3-4
3-2.
User-Configured Jumpers...................................................................................... 3-8
3-3.
INIIT02 Module Circuit Board Layout................................................................... 3-10
3-4.
Example of How to Isolate a Module Mounting Unit ............................................. 3-14
3-5.
Typical INIIR01 Module Slot Assignment in the Module Mounting Unit ................ 3-15
3-6.
INIIT03 Module Circuit Board Layout................................................................... 3-19
3-7.
Typical INIIL02 Module Slot Assignment in the Module Mounting Unit ................. 3-25
4-1.
INNIS01 Faceplate ................................................................................................. 4-2
4-2.
INIIT02 Faceplate .................................................................................................. 4-3
4-3.
INIIT03 Faceplate .................................................................................................. 4-7
A-1.
NTCL01 Connector Assignments and Jumper Locations, Revision F
Circuit Board......................................................................................................... A-1
A-2.
NTCL01 Termination Unit Cable Connections ........................................................ A-2
B-1.
NICL01 Connector Assignments and Jumpers, Revision D Circuit Board ...............B-1
B-2.
NICL01 Termination Module Cable Connections ....................................................B-2
C-1.
Jumper Configuration for Data Port (Port 1 or 2) ....................................................C-1
C-2.
Jumper Configuration for Diagnostic Port (Port 2 Only) ..........................................C-2
C-3.
Handshake Signal Jumpers (Normally Installed) ....................................................C-2
C-4.
Jumper Settings for J14 through J17 ....................................................................C-3
C-5.
Jumper Setting for J18 ..........................................................................................C-3
C-6.
NTMP01 Connector Assignments and Jumper Locations ........................................C-4
C-7.
NTMP01 Cable Connections...................................................................................C-4
D-1.
Jumper Configuration for Data Port (Port 1 or 2) ....................................................D-1
D-2.
Jumper Configuration for Diagnostic Port (Port 2 Only) ..........................................D-2
D-3.
Handshake Signal Schematic (Normally Installed) ..................................................D-2
D-4.
Jumper Settings for J14 through J17 ....................................................................D-3
D-5.
Jumper Setting for J18 ..........................................................................................D-3
D-6.
NIMP01 Connector Assignments and Jumper Locations .........................................D-4
D-7.
NIMP01 Cable Connections....................................................................................D-4
E-1.
Control of Redundant Communication Equipment .................................................E-2
E-2.
Redundant Transfer Modules Using One Termination Unit ....................................E-3
E-3.
Redundant Transfer Modules Using NIMP01 and NIMP02 Termination Modules ....E-4
E-4.
Redundant Transfer Modules Using Redundant Termination Units ........................E-4
E-5.
Redundant Transfer Modules with Redundant NIMP01 Termination Modules ........E-5
