Bacharach 67-7622 Installation & Operation Instruction Download Page 61

Page: 61 / 96

Instructions 67-9319

Bacharach, Inc.

Page 4-7

INJECTOR CALIBRATOR CD3

MAINTENANCE AND TROUBLESHOOTING

Figure 4-10. Fuel Arm O-Ring

Figure 4-11. Main Motor Reset

Figure 4-12. Flowmeter Limit Switches

4.2.3 Replacing O-ring in Fuel Arm

If calibration fluid is leaking at the fuel arm:

1. Pull cotter pin.

2. Tilt back clamp arm.

3. Lift out fuel connector and turn over. (Do not lose

spring and washer.)

4. Remove and replace O-ring.

5. Lower arm and reinstall the cotter pin.

4.2.4 Resetting Switches

Resetting the Motor Reset Button

In the event of a motor overload condition:

1. Remove the electrical box cover (lower left side

panel).

2. Press the main motor reset button.

3. Investigate why the motor was overloaded.

Resetting Flowmeter Limit Switches

If the flowmeter displays all zeros or will not display

flow readings, the limit switches may be tripped.

1. Disconnect power to the flowmeter by switching

the On/Off Switch (left side panel) to OFF.

2. Remove console rear cover.

3. Reposition the flowmeter piston so that the

adapter block is centered in the cavity.

4. Reconnect main power.

5. Restart the calibrator by switching ON the On/Off

Switch on the left side panel of the calibrator.

6. If the flowmeter again displays all zeros check the

optical detectors. They may have to be cleaned or

replaced.

7. Restart the calibrator.

8. If the flowmeter still will not work, the main

printed circuit board (PCB) may have to be

replaced, see Section 4.2.6.

4 O-ring

2 Main motor rest

3 Cavity (behind transducer)

Limit switch

6 Optical detectors

Limit switch

Summary of Contents for 67-7622

































































































Search results

Summary of Contents for 67-7622

Reviews:

Related manuals for 67-7622

Brands by name

Popular brands

Bacharach 67-7622, Installation & Operation Instruction

Search results

Summary of Contents for 67-7622

Reviews:

Related manuals for 67-7622

Brands by name

Popular brands