manualshive.com logo in svg

Bacharach 67-7622, Installation & Operation Instruction

Share
Download
Bacharach 67-7622 Installation & Operation Instruction Download Page 43

Instructions 67-9319

   

Bacharach, Inc.

Page 3-17

INJECTOR CALIBRATOR CD3

      OPERATION

Injector

Cam P/N

Cam ID

53, 71, 92 & 92 M

77-0610

53,71,92

149

67-6372

149

8.2L

77-0610

53,71,92

8. Fit the cam in place on the camshaft and make

sure key in the cam is properly seated.

NOTE:

  It is a good practice to check that

the cam does not wobble on the camshaft.

If wobble exists, dress the camshaft where

required as applicable.

9. Secure the cam with the washer and hex nut.

10. Remove pushrod lock.

The calibrator is now ready for mounting DD

Injectors. Procedures for mounting DD injectors

vary according to the style of the injector:

• Type 53, 71, 92 or 92 M

Section 3.9

• Type 149

Section 3.10

• Type 8.2 liter

Section 3.11

Follow the mounting procedure for the style

injector you have.

Figure 3-37. Cam & Hardware

6  Washer and Nut

5  Cam (Cam 189 Shown)

Summary of Contents for 67-7622

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands