Bacharach 67-7622 Installation & Operation Instruction Download Page 48

Page: 48 / 96

Page 3-22

Bacharach, Inc.

Instructions 67-9319

OPERATION

INJECTOR CALIBRATOR CD3

Figure 3-47. Injector Setup

Figure 3-48. Injector Clamping

Figure 3-49. Timing Light & Clamp Monitor

The air cylinders will retract and clamp injector.

11. Press the BODY TO SEAT CLAMP button.

12. Release BODY TO SEAT CLAMP button when

the BODY TO SEAT monitor turns green.

3.2.5.4 Fuel Inlet

13. Disconnect the fuel inlet tubing from the fuel

arm by unscrewing the knurled knob.

14. Swing the fuel arm back toward console.

15. Connect fuel inlet fitting to manifold INLET.

3.2.5.5 Injector

16. Lay the injector into the support.

17. Guide the spring and plunger of the injector

into the manifold block.

3.2.5.6 Injector Clamping

18. Push and hold the HOLD TO OPERATE button

with left hand.

19. While holding down the HOLD TO OPERATE

button, move the CLAMP/UNCLAMP lever to

the CLAMP position with right hand.

Maximum clamping force shown on the CLAMP

MONITOR/TIMING PLUNGER TO BODY gauge

will be in the green segment of the dial and the

PLUNGER TO BODY timing light will be lit.

20. Wait until the PLUNGER TO BODY timing

light goes out (after about 3 seconds).

21. Release the HOLD TO OPERATE button

first

and

then

the CLAMP/UNCLAMP lever. The

lever will return to the center position.

For clamping to occur correctly, you must follow

this sequence carefully.

The gauge reading will decrease from the green

segment of the dial to a lower reading (red seg-

ment) immediately after the CLAMP/UNCLAMP

valve lever is returned to the center position.

The injector is now ready for testing (Section 3.2.7).

Manifold Inlet

5 Discharge Head

Injector

6 Flowmeter Tubing

CLAMP

HOLD TO OPERATE

Plunger to Body

Clamp Monitor

Plunger to Body

Timing Light

Summary of Contents for 67-7622

































































































Search results

Summary of Contents for 67-7622

Reviews:

Related manuals for 67-7622

Brands by name

Popular brands

Bacharach 67-7622, Installation & Operation Instruction

Search results

Summary of Contents for 67-7622

Reviews:

Related manuals for 67-7622

Brands by name

Popular brands