manualshive.com logo in svg

Bacharach 67-7622, Installation & Operation Instruction

Share
Download
Bacharach 67-7622 Installation & Operation Instruction Download Page 47

Instructions 67-9319

   

Bacharach, Inc.

Page 3-21

INJECTOR CALIBRATOR CD3

      OPERATION

Figure 3-44. DD Type 149 Injector Accessories

Figure 3-45. Accessory Setup

Figure 3-46. Body to Seat Clamp

3.2.5 Mounting DD Injector Type 149

Before mounting injectors, check cambox to be sure

that cam 67-6372 (149) is mounted on the cam-

shaft.

3.2.5.1 Manifold

1. Place push rod extension (67-5708) over the

push rod.

2. Mount manifold block (67-7643) over dowels.

3. Attach the drain hose to the return fitting on

the manifold.

4. Lay the front injector support (67- 6605) over

the rails.

3.2.5.2 Discharge Head

5. Insert the discharge head (67-5700) into the

clamp cylinder socket with the quick connect

socket set for easy hose connection.

NOTE:

 

 When discharge heads are in-

stalled for the first time, wet O-ring with

calibration fluid for easier installation.

6. Insert the flowmeter tubing with the quick

connect plug into the discharge head.

3.2.5.3 Body to Seat Clamp

NOTE:

  The body-to-seat air clamping is

not needed for DD injectors. To keep them

out of the way, activate the air cylinders

and leave them in clamped position during

testing.

 7. Lift the pulley cover to expose the camshaft

pulleys and flywheel.

 8. Rotate flywheel by hand (barring tool inserted

in holes in the flywheel can help in turning the

flywheel) until the white painted area on the

flywheel shows through the window.

 9. Close the pulley cover. Cover must be closed for

the main drive motor to operate.

10. To clamp the injector, press and hold down the

HOLD TO OPERATE button

Manifold
Block

Drain
Fitting

Standoffs

Front
Support

Discharge
Head

Injector

Push Rod
Extension

3  Drain Hose

14

  Swing Fuel

       Arm Back

2  Manifold Block

4  Injector Support

11

  BODY TO SEAT CLAMP

10

  HOLD TO OPERATE

Summary of Contents for 67-7622

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands