Bacharach 67-7622 Installation & Operation Instruction Download Page 39

Page: 39 / 96

Instructions 67-9319

Bacharach, Inc.

Page 3-13

INJECTOR CALIBRATOR CD3

OPERATION

Figure 3-29. Injector Clamped

Figure 3-30. Testing Injectors

17. Connect the fuel inlet connector (using a Teflon

O-ring) to the injector inlet port (the inlet

orifice in the injector is visible).

18. Use the drain hose connector assembly (67-

6580) to connect to the injector return port.

19. Insert the hose into the hole of the drain pan.

The injector is now ready for testing (Section 3.1.8).

3.1.8 Testing

WARNING:

HAZARDOUS ROTATING MACHIN-

ERY. Do not open cambox cover while

main drive motor is running.

NOTE:

When starting main drive for the

first time, run it for only a few seconds

after pressure develops to make sure that

all fuel connections are tight.

1. Press the START MAIN DRIVE button.

NOTE:

If main drive motor won’t start,

check the pulley cover. It must be tightly

closed for the interlock safety switch to

allow the main drive motor to operate.

2. Wait until trapped air escapes from the dis-

charge head through the plastic tubing leading

to the meter. Rapid chattering indicates that air

is trapped in the tubing.

3. Check fuel pressure on the RAIL PRESSURE

gauge. It must be exactly 100 psi. If the RAIL

PRESSURE is above or below 100 psi, adjust it

by turning the Rail PRESSURE REGULATOR

and relocking the nut on the stem.

4. Set the STROKE selector on 50.

5. Press START METER on the console. The light

in the button will come on.

The MM

/STROKE delivery display will show

cumulative readings until 50 strokes are completed.

At that time the reading will stay on until the next

update which is after 50 strokes when the red dot

will flash. Readings will be updated automatically

every 50 strokes.

6. Observe the LED display and record fuel output

readings.

Flanged Injector

Swing Back Fuel Arm

Fuel Inlet Connector

Drain Connection

Drain Hose

1 Pulley

cover

4 Stroke

selector

5 Display of

Fuel output

7 Stop

5 Start

meter

3 Rail

pressure

1 Start

main drive

3 Rail pressure

regulator

Summary of Contents for 67-7622

































































































Search results

Summary of Contents for 67-7622

Reviews:

Brands by name

Popular brands

Bacharach 67-7622, Installation & Operation Instruction

Search results

Summary of Contents for 67-7622

Reviews:

Brands by name

Popular brands