manualshive.com logo in svg

Bacharach 67-7622, Installation & Operation Instruction

Share
Download
Bacharach 67-7622 Installation & Operation Instruction Download Page 42

Page 3-16

  

Bacharach, Inc.

         Instructions 67-9319

OPERATION

     INJECTOR CALIBRATOR CD3

Figure 3-34. Pulley

Figure 3-35. Changing Speed

Figure 3-36. Changing Cams

2. Open the hinged door on the left side of the

calibrator to expose the lower pulleys.

3. Insert barring tool into roller link assembly.

4. Push down on the barring tool to raise the

motor enough to shift the drive belt from one

set of pulleys to the other.

5. For 2000 RPM setting required for running the

DD injectors, move belt to the smaller diameter

pulley on camshaft (top) and the matching

pulley on the motor shaft (bottom).

6. Before lowering the motor, slide the motor

block shim (marked CUM) from under the

leveler, as it is not needed for DD injectors.

7. Lower the motor to its original position.

Next, check for proper cam installation (Sec. 3.2.3).

3.2.3  Changing Cams

The cam is secured in place on the tapered end of

the camshaft by a 3/4 in. hex nut and a 3/4 in. plain

washer, and is locked to the shaft by a key.

When shipped from the factory, the calibrator has

Cam 189 (67-6370) installed (used for most

Cummins injectors). To change the cam:

1. Switch the power On/Off Switch to OFF.

2. Raise hinged lids of the cambox and flywheel.

3. Insert barring tool into one of the radial holes

in the flywheel to hold camshaft in position.

4. Bar over flywheel until push rod is fully ex-

tended from cambox (cam at maximum lift).

5. Install push rod lock to hold the push rod when

the cam is being removed.

NOTE:

  Failure to do so can lead to

disengagement of follower parts and

subsequent early failure of cambox.

6. Using a 1-1/8 in. box wrench, unscrew and

remove the nut, washer and cam.

7. Select proper cam for the injector to be tested:

Using Cummins service publications as a guide.

5  For Cummins Use Large Pulley

6  Shim

3  Barring Tool

  (push down)

3  Barring Tool

2  Cambox Lid

6  Wrench

Summary of Contents for 67-7622

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands