Bacharach 67-7622 Installation & Operation Instruction Download Page 38

Page: 38 / 96

Page 3-12

Bacharach, Inc.

Instructions 67-9319

OPERATION

INJECTOR CALIBRATOR CD3

Figure 3-26. Body to Seat Clamp

Figure 3-27. Timing Light & Clamp Monitors

Figure 3-28. Plunger to Body Clamp

9. Press the BODY TO SEAT CLAMP button.

The air cylinders will retract and clamp the

injector.

10. Release the BODY TO SEAT CLAMP button

when the BODY TO SEAT monitor turns green.

3.1.7.3 Clamping Plunger to Body

CAUTION

Clamping force influences fuel delivery.

Follow these instructions carefully.

11. Continue to hold the HOLD TO OPERATE

button with left hand.

12. While holding down the HOLD TO OPERATE

button, move the CLAMP/UNCLAMP lever to

the CLAMP position with right hand.

The maximum clamping force shown on the

CLAMP MONITOR/TIMING PLUNGER TO BODY

gauge will be in the green segment and the timing

light will be lit.

13. Wait until the PLUNGER TO BODY timing

light goes out (after about 3 seconds).

14. Release the HOLD TO OPERATE button

first

and

then

the CLAMP/UNCLAMP lever. The

lever will return to the center position.

For clamping to occur correctly, you must follow

this sequence.

The gauge reading will decrease from the green

segment of the dial to a lower reading (red

segment) immediately after the CLAMP/UN-

CLAMP valve lever is returned to the center

position.

3.1.7.4 Connecting Fuel Inlet

15. With the flanged injector clamped in position,

disconnect the fuel inlet connector from the fuel

arm.

16. Swing the arm towards the console.

9 BODY TO SEAT CLAMP

8 HOLD TO OPERATE

Plunger to Body

Clamp Monitor

Plunger to Body Timing Light

Body to Seat

Clamp Monitor

CLAMP

HOLD TO OPERATE

Summary of Contents for 67-7622

































































































Search results

Summary of Contents for 67-7622

Reviews:

Related manuals for 67-7622

Brands by name

Popular brands

Bacharach 67-7622, Installation & Operation Instruction

Search results

Summary of Contents for 67-7622

Reviews:

Related manuals for 67-7622

Brands by name

Popular brands