manualshive.com logo in svg

Bacharach 67-7622, Installation & Operation Instruction

Share
Download
Bacharach 67-7622 Installation & Operation Instruction Download Page 64

Page 4-10

      

  Bacharach, Inc.

Instructions 67-9319

MAINTENANCE AND TROUBLESHOOTING

             INJECTOR CALIBRATOR CD3

4.3 Adjustments

4.3.1 Calibration Fluid Temperature

Adjustment

The CALIBRATION FLUID TEMPERATURE gauge

was calibrated at the factory to indicate the fluid

temperature about one inch upstream of the fuel arm.

This calibration was performed at stabilized

conditions using special fixtures and an electronic

digital thermometer.

Do not change the temperature gauge calibration

without use of a special fixture and procedure.

Bacharach supplies the procedure and special fixture

as part of the CD3 Calibrator Audit Kit (PN 67-7707)

4.3.2 Air Pressure Regulator Adjustment

Required air pressure is set at the factory to produce

the proper clamping force by the air cylinders and the

correct pressure for unlocking the hydraulic cylinder.

If for any reason it is necessary to change this setting:

1. The Primary Air Pressure Regulator should be

set at 90 ± 5 psi, the Secondary Air Pressure

Regulator must be set at 60 +5 -0 psi (4.1 bar).

The air pressure regulators are behind the lower

rear panel (See Section 2.3).

CAUTION

HIGH PRESSURE CAN DAMAGE AIR

REGULATOR.

  Shop air supply must be

less than 125 psi.

2. To adjust the Primary Air Pressure Regulator, lift

the ring on top of the regulator.

3. Hold the ring up and turn it to adjust the incom-

ing pressure to 90 psi.

4. Push the ring back down to lock the setting.

5. To adjust Secondary Air Pressure Regulator,

loosen locknut and turn adjusting screw clockwise

to increase and counterclockwise to decrease

pressure. Adjust to 60 +5 -0 psi.

6. Retighten the locknut.

Figure 4-15. Primary Air Pressure Regulator

Figure 4-16. Secondary Air Pressure Regulator

2  Red ring

2  Primary air pressure regulator

5  Secondary air pressure regulator

Summary of Contents for 67-7622

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands