Bacharach 67-7622 Installation & Operation Instruction Download Page 49

Page: 49 / 96

Instructions 67-9319

Bacharach, Inc.

Page 3-23

INJECTOR CALIBRATOR CD3

OPERATION

3.2.6 Mounting DD Injector Type 8.2 Liter

Before mounting injectors, check cambox to be sure

that cam 77-0610 (53, 71, 92, 92 Marine or 8.2 L) is

mounted on the camshaft.

You will need injector holder assembly 67-8525

which includes the adapter, two angle spacers, a

spacer block, and an injector holder with key.

3.2.6.1 Spacer Block

1. Attach the spacer block to the cambox over the

two dowel pins on the push rod guide.

NOTE:

Make sure the spacer block is

flush against the push rod guide.

3.2.6.2 Discharge Head

2. Install the discharge head (67-5696) into the

clamp cylinder socket with the quick connect

socket set for easy hose connection.

NOTE:

When discharge heads are in-

stalled for the first time, wet O-ring with

calibration fluid for easier installation.

3. Insert the flowmeter tube with the quick

connect plug into the discharge head.

3.2.6.3 Body to Seat Clamp

NOTE:

The body-to-seat air clamping

is not needed for 8.2 Liter injectors. To

keep them out of the way, activate the air

cylinders and leave them in clamped

position during testing.

4. Lift the pulley cover to expose the camshaft

pulleys and flywheel.

5. Rotate flywheel by hand (the barring tool in-

serted in holes in flywheel can help in turning

the flywheel) until the white painted area on

the flywheel shows through the window.

6. Close the pulley cover. Cover must be closed for

the main drive motor to operate.

7. To clamp the injector, press and hold down the

HOLD TO OPERATE button

Figure 3-50. DD Type 8.2 Liter Injector

Accessories

Figure 3-51. Accessory Setup

Figure 3-52. Body to Seat Clamp

Spacer Block

Injector Holder

Discharge Head

Injector

Key

1 Cambox

1 Push rod guide

1 Spacer block

1 Dowl pin

3 Flowmeter tube

2 Discharge head

8 BODY TO SEAT CLAMP

7 HOLD TO OPERATE

Summary of Contents for 67-7622

































































































Search results

Summary of Contents for 67-7622

Reviews:

Related manuals for 67-7622

Brands by name

Popular brands

Bacharach 67-7622, Installation & Operation Instruction

Search results

Summary of Contents for 67-7622

Reviews:

Related manuals for 67-7622

Brands by name

Popular brands