Bacharach 67-7622 Installation & Operation Instruction Download Page 40

Page: 40 / 96

Page 3-14

Bacharach, Inc.

Instructions 67-9319

OPERATION

INJECTOR CALIBRATOR CD3

The reading is in mm

/stroke, which is equivalent to

/1000 strokes (cc/1000 strokes). During a test

run, if a change over is made from 50 to 100 stroke

setting, or vice versa, ignore the next reading

7. When the test is over, press the STOP button

on the left hand operator’s table.

3.1.9 Unclamping

1. Disconnect the fuel inlet.

2. Press and hold the HOLD TO OPERATE

button.

3. While holding the button down, move the

CLAMP/UNCLAMP lever to the UNCLAMP

position and let the hydraulic cylinder

completely retract.

4. Release the HOLD TO OPERATE push-button

and allow the CLAMP/UNCLAMP lever to

return to its center position.

5. Press the BODY TO SEAT RELEASE button,

and hold down until the BODY TO SEAT green

indicator retracts.

3.1.10

Removing Injectors & Shutting Down

1. Disconnect the fuel inlet hose from the injector

holder or manifold.

2. Remove injector and accessories from the

calibrator.

3. Replace accessories on inside cabinet door.

4. Disconnect flowmeter tubing from discharge

head.

5. Remove discharge head and store inside the

cabinet door.

6. Remove cam and store inside the cabinet door.

NOTE:

Discharge head and cam can be

left installed on the calibrator if desired.

7. Turn off power at On/Off Switch at lower left

side of calibrator.

8. Wipe oil spills and splashes from console and

operator’s table.

Figure 3-31. Unclamping Injectors

3 UNCLAMP

2 HOLD TO OPERATE

Summary of Contents for 67-7622

































































































Search results

Summary of Contents for 67-7622

Reviews:

Related manuals for 67-7622

Brands by name

Popular brands

Bacharach 67-7622, Installation & Operation Instruction

Search results

Summary of Contents for 67-7622

Reviews:

Related manuals for 67-7622

Brands by name

Popular brands