manualshive.com logo in svg

Bacharach 67-7622, Installation & Operation Instruction

Share
Download
Bacharach 67-7622 Installation & Operation Instruction Download Page 3

Instruction 67-9319

     

Bacharach, Inc.

 i

TABLE OF CONTENTS

1.0 INTRODUCTION ............................................................................................................. 1-1

1.1 Calibrator Features .................................................................................................. 1-1

1.2 Accessories ................................................................................................................ 1-5

1.3 Construction .............................................................................................................. 1-6

1.4 Calibration Fluid System ........................................................................................  1-7

1.5 Calibration Fluid Temperature Control System ................................................... 1-10

1.6 Pneumatic System .................................................................................................. 1-11

1.7 Electrical System .................................................................................................... 1-11

2.0 INSTALLATION ............................................................................................................... 2-1

2.1 Selecting the Site ...................................................................................................... 2-1

2.2 Hold Downs ............................................................................................................... 2-1

2.3 Utility Connections ................................................................................................... 2-2

2.4 Filling Reservoirs ...................................................................................................... 2-3

2.5 Pre-operation Checks................................................................................................ 2-4

2.6 Initial Checks ............................................................................................................ 2-4

2.7 Start-up ..................................................................................................................... 2-6

2.8 Repacking for Shipping ............................................................................................ 2-7

2.9 Shipping and Storage ............................................................................................... 2-7

3.0 OPERATION ..................................................................................................................... 3-1

3.1 Cummins Injectors.................................................................................................... 3-1

3.1.1 Quick Reference Chart .................................................................................. 3-1

3.1.2 Changing Speed ............................................................................................. 3-2

3.1.3 Changing Cams ............................................................................................. 3-3

3.1.4 Inserting the Cummins Discharge Head ...................................................... 3-4

3.1.5 Mounting Cummins Type PTD Cylindrical Injectors .................................. 3-5

3.1.6 Mounting Cummins Types PTB and PTC Cylindrical Injectors ................. 3-8

3.1.7 Mounting Flanged Injectors ........................................................................ 3-11

3.1.8 Testing ......................................................................................................... 3-13

3.1.9 Unclamping .................................................................................................. 3-44

3.1.10 Removing Injectors and Shutting Down Calibrator ................................... 3-14

3.2 Detroit Diesel (DD) Injectors.................................................................................. 3-15

3.2.1 Quick Reference Chart ................................................................................ 3-15

3.2.2 Changing Speed ........................................................................................... 3-15

3.2.3 Changing Cams ........................................................................................... 3-16

3.2.4 Mounting DD Injector Types 53, 71, and 92 ............................................... 3-18

3.2.5 Mounting DD Injector Type 149 ................................................................. 3-21

3.2.6 Mounting DD Injector Type 8.2 Liter ......................................................... 3-23

3.2.7 Testing ......................................................................................................... 3-25

3.2.8 Unclamping .................................................................................................. 3-27

3.2.9 Removing Injectors and Shutting Down Calibrator ................................... 3-28

Summary of Contents for 67-7622

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands