Bacharach 67-7622 Installation & Operation Instruction Download Page 53

Page: 53 / 96

Instructions 67-9319

Bacharach, Inc.

Page 3-27

INJECTOR CALIBRATOR CD3

OPERATION

3.2.8 Unclamping

1. Disconnect the fuel inlet.

2. Press & hold the HOLD TO OPERATE button.

3. While holding button down, move the CLAMP/

UNCLAMP lever to UNCLAMP position and let

the hydraulic cylinder completely retract.

4. Release the HOLD TO OPERATE push-button

and allow the CLAMP/UNCLAMP lever to

return to its center position.

DD Type 8.2 Liters injectors

a. Lift the key from the injector holder slot.

b. Place the two angle spacers from the

injector holder assembly (67-8525) over the

rails between the cambox and injector.

c. Press & hold HOLD TO OPERATE button.

Gradually move the CLAMP/UNCLAMP

lever to CLAMP position to extend clamp-

ing cylinder until the injector holder butts

against the angle spacers next to cambox.

Injector will "pop" out of injector holder.

d. Repeat steps 3 & 4 again.

3.2.9 Removing Injectors & Shutting Down

1. Disconnect the fuel inlet hose from the injector

holder or manifold.

2. Remove injector & accessories from calibrator.

3. Return accessories on inside cabinet door.

4. Disconnect flowmeter tubing from discharge

head.

5. Remove discharge head & store inside cabinet.

6. Remove cam and store inside the cabinet door.

NOTE:

Discharge head and cam can be

left installed on the calibrator if desired.

7. Turn off power at On/Off Switch at lower left

side of calibrator.

8. Wipe oil spills and splashes from console and

operator’s table.

Figure 3-57. Unclamping Injectors

Figure 3-58. Unclamping DD 8.2L Injectors

3 UNCLAMP

2 HOLD TO OPERATE

4 Angle spacer

4 8.2L Injector holder

4 Key

Summary of Contents for 67-7622

































































































Search results

Summary of Contents for 67-7622

Reviews:

Related manuals for 67-7622

Brands by name

Popular brands

Bacharach 67-7622, Installation & Operation Instruction

Search results

Summary of Contents for 67-7622

Reviews:

Related manuals for 67-7622

Brands by name

Popular brands